I flipped the spindle nut over upside down in a drill press vise and I drilled (4) 1-1/2" deep holes (5/32 drill bit), spaced about 1/2" apart along the length of the main nut, down through the bottom and through the crack/break. CONTACT YOST. Wood Nut for a Wood Vice Screw: In the construction of my leg vice, by the grace of the cosmos I came into possession of this huge wood screw. Get the best deals on vise screw when you shop the largest online selection at eBay.com. Service: support@yostvises.com Bench screw & nut woodworking vise collectible carpentry wood holding tool S2. Category. I screwed in 4 10-32 x 2" screws as far as I could with vise grips until they broke off. Wood Nut for a Wood Vice Screw: In the construction of my leg vice, by the grace of the cosmos I came into possession of this huge wood screw.

In order to mount it a couple holes need to be drilled first. PRODUCTS. Screw & Nut Kit (11) Base Kit (6) Serrated Jaws (17) Pipe Jaws (5) Smooth Jaws (7) Compare Products . Base plate 68 x 68 mm. Menu Cart 0. Screw & Nut Kit (11 Products) Base Kit (6 Products) Serrated Jaws (17 Products) Pipe Jaws (5 Products) Smooth Jaws (7 Products) Browse By. PRODUCTS. It's is about a 1/2 inch, 10 TPI acme thread. Code 300671 Price ∗ € 16.90. Vintage Bench Tail Vise Screw Workbench Woodworking. The tensile strength of the joint won't be high and it'll break with a bit of tightening. The leveling leg comes with a nut originally used to adjust the height of the scaffold. Watch. Vise Kits for Leg Vises, Tail Vises, Twin Screw Vises and Face Vises. $25.95 shipping. Once dismantled the dove tail, gib, jaws, etc all look in reasonable order, but the feed screw and nut (not sure it that is the correct term for a vice but you know what I mean) are stripped and need to be replaced. The self-locking property is also key to the screw's use in a wide range of other applications, such as the corkscrew , screw top container lid, threaded pipe joint, vise , C-clamp , and screw jack . $25.95 shipping. level 1. $49.99. Use a couple of socket head bolts to bolt the new piece to the nut, Tap the nut perpendicular to the vise screw and also use a dowel pin or two to take the shear load. Vise Selection Chart. Once dismantled the dove tail, gib, jaws, etc all look in reasonable order, but the feed screw and nut (not sure it that is the correct term for a vice but you know what I mean) are stripped and need to be replaced. Pressure piece D1. Cast Iron Nut M32. Service: support@yostvises.com Pressure piece D1. Email: sales@yostvises.com.

I’ll use this as the capture nut mounted inside the workbench. The dowels will be necessary otherwise the bolts will work loose quickly. $49.99. thanks Larry Code 300671 Price ∗ € 16.90. Turn a round nut with a flange on one end and make sure that it's 'pulling' into the hole you bore in the cast iron nut when the vice is tightened. In these instructions when we refer to the “front” of the vise or nut/screw assembly, we mean the end that has the hex for the handle and is closest to the operator. I used a flush cut bit on my router, with an undersized bearing, …

It's is about a 1/2 inch, 10 TPI acme thread. VINTAGE OHIO TOOL Company Wooden Vise Screw And Nut, 2-3/8” Dia - $75.00. A rare set up with a 27 inch screw and the original wooden nut made by the Ohio tool company. Don't bother trying to braze it back together. Phone: (616) 396-2063 Fax: (616) 396-8276. I then tapped the 4 holes with a 10-32 tap. for German and Scandinavian Vise Screw fits code 300659 Note: M32 is the maker's code and not a thread size!

My screw nut that broke is on an Ohio Forge 6" vise, but looks similar to this nut.

HDL(M)6 Nut/Screw Assembly Remove, repair, and reassemble the nut and screw assembly in your HDL series double lock vise. Cast Iron Nut M32. Bench screw & nut woodworking vise collectible carpentry wood holding tool S2. The screw that I used for the leg vise was a scaffold leveling leg. Vise Kits for Leg Vise, Tail Vise, Twin Screw Vise, Face Vise, Leg Vice, Tail Vice, Twin Screw Vice, Face Vice, Wood Vise, Wood Vice, Workbench. * 1 star 2 stars 3 stars 4 stars 5 stars; Quality *Nickname *Summary of Your Review *Review. It is frequently the case that the nut on a bench-vise screw breaks from being subjected to a too violent strain. Email: sales@yostvises.com. It is … I am trying to confirm the nut dimensions of the Craftsman nut. Top Rated Plus. CONTACT YOST. 1 PAIR (2PC) 8" WOOD CLAMPS HAND SCREW CLAMP WOODEN VISE VICE HANDSCREW. for German and Scandinavian Vise Screw fits code 300659 Note: M32 is the maker's code and not a thread size! You're reviewing: Screw and Nut Kit for vise model #: 34C, 134C How do you rate this product? Rowan Sylvester-Bradley: 20/03/2020 13:56:07 for German and Scandinavian Vise Screw fits code 300659. 1) On the vise face near the handle, there is no need to drill the hole in the face as large as the hole you'll drill in the rear face to accept the nut. The Classic uses the same double-lead acme screw as our Glide Leg Vise and moves as fast as typical wooden vise screws, ½” of travel per turn.